Fuel tank removal

Seats, middle fairings, hoses, pump connector, tank — Kawasaki Ninja 400 (2018–2023), 16 steps.

Category: Fuel system

From the Fuel System (DFI) chapter, Fuel Tank Removal. Gasoline is extremely flammable: work on a cold engine, in a ventilated area, away from flames and sparks. Step texts are condensed; check the manual pages.

  1. Step 1: Preparation

    Turn the ignition switch off and wait until the engine cools down. Keep a cloth ready for spilled fuel.

    Parts: Fuel Tank

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

  2. Step 2: Rear seat

    Unlock with the key, pull up the front part of the rear seat and remove it.

    Parts: Rear Seat

    Manual: Ch. 15 Frame › Seats

  3. Step 3: Front seat

    Pull the seat lock cable backward, lift the rear part of the front seat and remove it.

    Parts: Front Seat

    Manual: Ch. 15 Frame › Seats

  4. Step 4: Battery negative terminal

    Disconnect the battery (−) cable.

    Parts: Battery Negative (-) Cable / Engine Ground Lead, Battery (sealed, FTX9-BS)

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

  5. Step 5: Side covers

    Remove the bolts and pull each cover outward out of the grommets.

    Parts: Side Cover (left), Side Cover (right)

    Manual: Ch. 15 Frame › Side Cover Removal/Installation

  6. Step 6: Lower fairings

    Remove the lower fairings on both sides: the middle fairings cannot come off before them.

    Parts: Lower Fairing (left), Lower Fairing (right)

    Manual: Ch. 15 Frame › Fairings

  7. Step 7: Lower inner fairing

    Remove the lower inner fairing as well; it also has to be off before the middle fairings.

    Parts: Lower Inner Fairing

    Manual: Ch. 15 Frame › Fairings

  8. Step 8: Middle fairings

    Disconnect the turn signal connectors, remove the bolts and take off the middle fairings on both sides.

    Parts: Upper Middle Fairing (left), Upper Middle Fairing (right), Lower Middle Fairing (left), Lower Middle Fairing (right), Fin (left middle fairing), Fin (right middle fairing), Turn Signal Light Cover (left), Turn Signal Light Cover (right), Bracket (left middle fairing, rear blade), Bracket (left middle fairing, at turn signal), Front Turn Signal Light (left) with bracket, Front Turn Signal Light (right) with bracket, Front Turn Signal Lens (left), Front Turn Signal Lens (right)

    Manual: Ch. 15 Frame › Fairings; Ch. 15 Frame › Middle Fairing Installation

  9. Step 9: Middle fairing pads

    Take off the foam pads that sit behind the middle fairings (in the manual the pad is fitted on the left side only).

    Parts: Pads (middle fairing)

    Manual: Ch. 15 Frame › Fairings

  10. Step 10: Upper inner fairing at the tank

    Remove the bolt on both sides and clear the projection of the upper inner fairing from the grommet on both sides.

    Parts: Upper Inner Fairing

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

  11. Step 11: Drain and breather hoses

    Slide the clamps and disconnect the drain hose and the breather hose from the tank.

    Parts: Drain Hose (fuel tank), Breather Hose (fuel tank)

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

  12. Step 12: Tank bolts and rear bracket

    Remove the fuel tank bolts and the bracket.

    Parts: Bracket (fuel tank rear hold-down), Pad (fuel tank rear bracket)

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

  13. Step 13: Fuel pump connector

    Disconnect the fuel pump lead connector.

    Parts: Fuel Pump Lead Connector

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

  14. Step 14: Release pressure and draw off fuel

    Open the fuel tank cap to lower the pressure in the tank. Draw the fuel out through the filler opening with a pump, then close the cap.

    Parts: Fuel Tank Cap

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

  15. Step 15: Fuel hose

    Pull up the rear of the tank. Wrap a cloth around the fuel hose joint and wipe off dirt. Open the joint lock (with fingers, or a flat screwdriver in its slit, without prying it wide) and disconnect the hose from the pump outlet pipe.

    Parts: Fuel Hose (high pressure, with joints), Fuel Outlet Pipe (fuel pump)

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

  16. Step 16: Lift off the tank

    Lift the tank and remove it from the motorcycle together with the fuel pump. Put it on a flat surface with the pipes closed off.

    Parts: Fuel Tank, Fuel Tank Cap, Water Drain Pipe / Fuel Breather Pipe (in tank), Fuel Pump mounting plate (flange), Fuel Pump Gasket, Fuel pump inlet strainer, Fuel pump motor (pump body), Fuel pump upper housing (filter, pressure regulator), Fuel Outlet Pipe (fuel pump), Fuel Level Sensor

    Manual: Ch. 3 Fuel System (DFI) › Fuel Tank Removal

The tank is off. The air cleaner housing and the throttle body assembly are now accessible.

Service manual

More procedures